Home / Shop by part type / Wide Angle (C.V.) Shafts / OH67513634
125 HP Half Shaft, Implement End — 1 3/4" x 6 implement end, 68"–107"
OH67513634 · P675 series · Half Shaft, Implement End
$875
This is one half of a driveline. A implement end (outer drive tube) on its own will not drive the implement — you also need the matching tractor end in the same P675 series. The options are listed below.
Specification
- Product family
- Wide Angle (C.V.) Shafts
- Series
- P675
- Tier
- Upgrade
- Position
- Implement end (outer drive tube)
- End yoke
- 1 3/4" x 6 splines clamp yoke
- Implement spline
- 1 3/4" x 6
- Cross journal diameter
- 36/42 mm (1.42/1.65")
- Cross length
- 89/104 mm (3.50/4.09")
- Closed, cross to cross
- 54" (137 cm)
- Open, cross to cross
- 93" (236 cm)
- Closed length (collapsed)
- 68" (173 cm)
- Open length (extended)
- 107" (272 cm)
- Power at 540 rpm
- 125 hp
- Power at 1000 rpm
- 200 hp
- Decoded
- Plain half shaft, implement end
Match the tractor, not the implement. The shaft’s rating must meet or exceed your tractor’s PTO horsepower. Undersize it and the driveline becomes the part that fails.
Check your PTO speed. This shaft is rated 125 hp at 540 rpm and 200 hp at 1000 rpm. Use the figure for the speed you actually run — they are not interchangeable.
Working it hard? Bare Co advise reducing the rated horsepower by 40% for severe conditions — shock loading, heavy or wet crop, stony ground.
Length
Closed is the shaft fully collapsed — its shortest. Open is fully extended — its longest. Your tractor and implement must sit inside that range at every point through the turn.
Cross to cross is measured between the centres of the two universal joints. Overall is the full length including the end yokes. Most machine specs quote cross to cross.
This shaft trims to length. Measure your machine at its shortest point — the shaft must not bottom out — then cut to suit. You can always take metal off; you cannot put it back.
COMPLETES THIS DRIVELINE
FITS THESE MACHINES
| Machine | Position | Tier |
|---|---|---|
| Case IH LBX331P/R/S | Implement end | P675 upgrade |
| Case IH LBX332P/R/S | Implement end | P675 upgrade |
| Case IH LBX421S/R | Implement end | P675 upgrade |
| Case IH LBX422R/S | Implement end | P675 upgrade |
| Case IH LBX431R | Implement end | P675 upgrade |
| Case IH LBX432R/S | Implement end | P675 upgrade |
| Case IH LBX431S | Implement end | P675 upgrade |
| Case IH BB940AP/AR/AS/P/R/S | Implement end | P675 upgrade |
| Case IH BB960S/R/AR/AS | Implement end | P675 upgrade |
| Case IH 590 | Implement end | P675 upgrade |
| Claas Quadrant 1150 | Implement end | P675 upgrade |
| Claas Quadrant 2100 | Implement end | P675 upgrade |
| Claas Quadrant 2200 | Implement end | P675 upgrade |
| Claas Quadrant 3200 | Implement end | P675 upgrade |
| Claas Quadrant 3300 | Implement end | P675 upgrade |
| Claas Quadrant 3400 | Implement end | P675 upgrade |
| Claas Big Pack 4X4 HX-XC | Implement end | P675 upgrade |
| Krone Big Pack 12130 | Implement end | P675 upgrade |
| Krone Big Pack 12130 XC | Implement end | P675 upgrade |
| Krone Big Pack 4X4 | Implement end | P675 upgrade |
| Krone Big Pack 4X4 HS | Implement end | P675 upgrade |
| Krone Big Pack 4X4 HX-XC | Implement end | P675 upgrade |
OTHER OPTIONS IN THIS SERIES
$875
1 3/8" x 6 implement end
$875
1 3/4" x 20 implement end
$809
half shaft, implement end, less yoke