Home / Shop by part type / Wide Angle (C.V.) Shafts / W361506
110 HP Wide Angle CV Driveline — 1 3/8" x 6 tractor, 1 3/4" x 6 implement, 77"–116"
W361506 · W2580 series · Wide Angle CV Driveline
$1,582
Specification
- Product family
- Wide Angle (C.V.) Shafts
- Series
- W2580
- Tier
- Heavy duty upgrade
- Position
- Complete driveline
- End yoke
- Complete wide angle shaft
- Tractor spline
- 1 3/8" x 6
- Implement spline
- 1 3/4" x 6
- Cross journal diameter
- 32/36 mm (1.26/1.42")
- Cross length
- 89/106 mm (3.50/4.17")
- Closed, cross to cross
- 63" (160 cm)
- Open, cross to cross
- 102" (259 cm)
- Closed length (collapsed)
- 77" (196 cm)
- Open length (extended)
- 116" (295 cm)
- Power at 540 rpm
- 110 hp
- Power at 1000 rpm
- 170 hp
- Decoded
- Wide angle complete shaft
Match the tractor, not the implement. The shaft’s rating must meet or exceed your tractor’s PTO horsepower. Undersize it and the driveline becomes the part that fails.
Check your PTO speed. This shaft is rated 110 hp at 540 rpm and 170 hp at 1000 rpm. Use the figure for the speed you actually run — they are not interchangeable.
Working it hard? Bare Co advise reducing the rated horsepower by 40% for severe conditions — shock loading, heavy or wet crop, stony ground.
Length
Closed is the shaft fully collapsed — its shortest. Open is fully extended — its longest. Your tractor and implement must sit inside that range at every point through the turn.
Cross to cross is measured between the centres of the two universal joints. Overall is the full length including the end yokes. Most machine specs quote cross to cross.
This shaft trims to length. Measure your machine at its shortest point — the shaft must not bottom out — then cut to suit. You can always take metal off; you cannot put it back.
Complete shaft. Halves matched by spline from the pto16 table; Bare Co do not state the build for W2580 on that page: IHW36150 + OH36150634. Both halves already stocked. Dealer cost not yet captured.
FITS THESE MACHINES
| Machine | Position | Tier |
|---|---|---|
| Case IH LBX331P/R/S | Front driveline | Standard |
| Case IH LBX332P/R/S | Front driveline | Standard |
| Case IH LBX421S/R | Front driveline | Standard |
| Case IH LBX422R/S | Front driveline | Standard |
| Case IH LBX431R | Front driveline | Standard |
| Case IH LBX432R/S | Front driveline | Standard |
| Case IH LBX431S | Front driveline | Standard |
| Case IH BB940AP/AR/AS/P/R/S | Front driveline | Standard |
| Case IH BB960S/R/AR/AS | Front driveline | Standard |
| Case IH 590 | Front driveline | Standard |
| New Holland 230P/PC | Front driveline | Standard |
| New Holland 330/PC/R | Front driveline | Standard |
| New Holland 340P/R | Front driveline | Standard |
| New Holland 870P/PC/R | Front driveline | Standard |
| New Holland 930A | Front driveline | Standard |
| New Holland 940 | Front driveline | Standard |
| New Holland 940A | Front driveline | Standard |
| New Holland 940R | Front driveline | Standard |
| New Holland 940S | Front driveline | Standard |
| Krone Big Pack 12130 | Front driveline | Standard |
| Krone Big Pack 12130 XC | Front driveline | Standard |
| Krone Big Pack 4X4 | Front driveline | Standard |
| Krone Big Pack 4X4 HS | Front driveline | Standard |
| Krone Big Pack 4X4 HX-XC | Front driveline | Standard |
OTHER OPTIONS IN THIS SERIES
