Home / Shop by part type / Wide Angle (C.V.) Shafts / WS6150216
64 HP Wide Angle CV Driveline with Shear Bolt Yoke — 1 3/8" x 21 tractor, 1 3/8" x 6 implement, 75"–114"
WS6150216 · 6 Series · Wide Angle CV Driveline with Shear Bolt Yoke
$1,049
Specification
- Product family
- Wide Angle (C.V.) Shafts
- Series
- 6 Series
- Tier
- Standard
- Position
- Tractor to baler
- End yoke
- Shear bolt yoke
- Tractor spline
- 1 3/8" x 21
- Implement spline
- 1 3/8" x 6
- Cross journal diameter
- 27/32 mm (1.06/1.26")
- Cross length
- 76/94 mm (2.99/3.70")
- Closed, cross to cross
- 63" (160 cm)
- Open, cross to cross
- 102" (259 cm)
- Closed length (collapsed)
- 75" (191 cm)
- Open length (extended)
- 114" (290 cm)
- Power at 540 rpm
- 64 hp
- Power at 1000 rpm
- 100 hp
- Decoded
- Wide angle with shear bolt yoke
Match the tractor, not the implement. The shaft’s rating must meet or exceed your tractor’s PTO horsepower. Undersize it and the driveline becomes the part that fails.
Check your PTO speed. This shaft is rated 64 hp at 540 rpm and 100 hp at 1000 rpm. Use the figure for the speed you actually run — they are not interchangeable.
Working it hard? Bare Co advise reducing the rated horsepower by 40% for severe conditions — shock loading, heavy or wet crop, stony ground.
Length
Closed is the shaft fully collapsed — its shortest. Open is fully extended — its longest. Your tractor and implement must sit inside that range at every point through the turn.
Cross to cross is measured between the centres of the two universal joints. Overall is the full length including the end yokes. Most machine specs quote cross to cross.
This shaft trims to length. Measure your machine at its shortest point — the shaft must not bottom out — then cut to suit. You can always take metal off; you cannot put it back.
FITS THESE MACHINES
| Machine | Position | Tier |
|---|---|---|
| John Deere 435 | Tractor to baler | Standard |
| John Deere 446 | Tractor to baler | Standard |
| John Deere 447 | Tractor to baler | Standard |
| John Deere 448 | Tractor to baler | Standard |
| John Deere 456 | Tractor to baler | Standard |
| John Deere 457 | Tractor to baler | Standard |
| John Deere 458 | Tractor to baler | Standard |
| John Deere 466 | Tractor to baler | Standard |
| John Deere 467 | Tractor to baler | Standard |
| John Deere 468 | Tractor to baler | Standard |
| John Deere 469 | Tractor to baler | Standard |
| John Deere 535 | Tractor to baler | Standard |
| John Deere 546 | Tractor to baler | Standard |
| John Deere 547 | Tractor to baler | Standard |
| John Deere 556 | Tractor to baler | Standard |
| John Deere 557 | Tractor to baler | Standard |
| John Deere 558 | Tractor to baler | Standard |
| John Deere 566 | Tractor to baler | Standard |
| John Deere 567 | Tractor to baler | Standard |
| John Deere 568 | Tractor to baler | Standard |
| John Deere 569 | Tractor to baler | Standard |
| Krone KR100 | Tractor to baler | Standard |
| Krone KR125 | Tractor to baler | Standard |
| Krone KR155 | Tractor to baler | Standard |
| Krone KR130 | Tractor to baler | Standard |
| Krone KR160 | Tractor to baler | Standard |
| Krone 1250 | Tractor to baler | Standard |
| Krone 1250MC | Tractor to baler | Standard |
| Krone 1500 | Tractor to baler | Standard |
| Krone 1500MC | Tractor to baler | Standard |
| Krone 1500V | Tractor to baler | Standard |
| Krone 1550 | Tractor to baler | Standard |
| Krone 1800 | Tractor to baler | Standard |
| Krone F55 | Tractor to baler | Standard |
| Krone F1250MC | Tractor to baler | Standard |
| Krone RP1250MC | Tractor to baler | Standard |
| Krone RP1550MC | Tractor to baler | Standard |
| Krone V180 | Tractor to baler | Standard |
| Krone V1500MC | Tractor to baler | Standard |
| Krone V1800MC | Tractor to baler | Standard |
| Massey Ferguson MF1745 | Tractor to baler | Standard |
| Challenger RB452 | Tractor to baler | Standard |
| Hesston 745 | Tractor to baler | Standard |
| New Idea 6254 | Tractor to baler | Standard |
OTHER OPTIONS IN THIS SERIES
$1,049
1 3/8" x 6 tractor end
$1,049
1 3/8" x 6 tractor end · 1 3/8" x 21 implement end
$1,274
wide angle cv driveline with slip clutch · 1 3/8" x 6 tractor end
$1,274
wide angle cv driveline with slip clutch
$1,274
wide angle cv driveline with slip clutch · 1 3/8" x 6 tractor end
$1,274
wide angle cv driveline with slip clutch · 1 3/8" x 21 implement end
$1,261
wide angle cv driveline with torque limiter · 1 3/8" x 6 tractor end