Home / Shop by part type / Wide Angle (C.V.) Shafts / WT6150
64 HP Wide Angle CV Driveline with Torque Limiter — 1 3/8" x 6 both ends, 75"–114"
WT6150 · 6 Series · Wide Angle CV Driveline with Torque Limiter
$1,261
Specification
- Product family
- Wide Angle (C.V.) Shafts
- Series
- 6 Series
- Tier
- Standard
- Position
- Tractor to baler
- End yoke
- Torque limiting yoke
- Tractor spline
- 1 3/8" x 6
- Implement spline
- 1 3/8" x 6
- Cross journal diameter
- 27/32 mm (1.06/1.26")
- Cross length
- 76/94 mm (2.99/3.70")
- Closed, cross to cross
- 63" (160 cm)
- Open, cross to cross
- 102" (259 cm)
- Closed length (collapsed)
- 75" (191 cm)
- Open length (extended)
- 114" (290 cm)
- Power at 540 rpm
- 64 hp
- Power at 1000 rpm
- 100 hp
- Decoded
- Wide angle with torque limiting yoke
Match the tractor, not the implement. The shaft’s rating must meet or exceed your tractor’s PTO horsepower. Undersize it and the driveline becomes the part that fails.
Check your PTO speed. This shaft is rated 64 hp at 540 rpm and 100 hp at 1000 rpm. Use the figure for the speed you actually run — they are not interchangeable.
Working it hard? Bare Co advise reducing the rated horsepower by 40% for severe conditions — shock loading, heavy or wet crop, stony ground.
Length
Closed is the shaft fully collapsed — its shortest. Open is fully extended — its longest. Your tractor and implement must sit inside that range at every point through the turn.
Cross to cross is measured between the centres of the two universal joints. Overall is the full length including the end yokes. Most machine specs quote cross to cross.
This shaft trims to length. Measure your machine at its shortest point — the shaft must not bottom out — then cut to suit. You can always take metal off; you cannot put it back.
FITS THESE MACHINES
| Machine | Position | Tier |
|---|---|---|
| Massey Ferguson MF1745 | Tractor to baler | Standard |
| Challenger RB452 | Tractor to baler | Standard |
| Hesston 745 | Tractor to baler | Standard |
| New Idea 6254 | Tractor to baler | Standard |
| Vermeer 504 I | Tractor to baler | Standard |
| Vermeer 504F | Tractor to baler | Standard |
| Vermeer 504H | Tractor to baler | Standard |
| Vermeer 504G | Tractor to baler | Standard |
| Vermeer 504MCL | Tractor to baler | Standard |
| Vermeer 505MCL | Tractor to baler | Standard |
| Vermeer 5400 REBEL | Tractor to baler | Standard |
| Vermeer 5410 REBEL | Tractor to baler | Standard |
| Vermeer 5500 REBEL | Tractor to baler | Standard |
OTHER OPTIONS IN THIS SERIES
$1,049
wide angle cv driveline with shear bolt yoke
$1,049
wide angle cv driveline with shear bolt yoke · 1 3/8" x 21 tractor end
$1,049
wide angle cv driveline with shear bolt yoke · 1 3/8" x 21 implement end
$1,274
wide angle cv driveline with slip clutch
$1,274
wide angle cv driveline with slip clutch · 1 3/8" x 21 tractor end
$1,274
wide angle cv driveline with slip clutch · 1 3/8" x 21 implement end
$1,274
wide angle cv driveline with slip clutch · 1 3/8" x 21 tractor end