Home / Shop by part type / Wide Angle (C.V.) Shafts / OH3615020

110 HP Half Shaft, Implement End — 1 3/4" x 20 implement end, 66"–105"

OH3615020 · W2580 series · Half Shaft, Implement End

$330

This is one half of a driveline. A implement end (outer drive tube) on its own will not drive the implement — you also need the matching tractor end in the same W2580 series. The options are listed below.

Specification

Product family: Wide Angle (C.V.) Shafts
Series: W2580
Tier: Standard
Position: Implement end (outer drive tube)
End yoke: 1 3/4" x 20 splines clamp yoke
Implement spline: 1 3/4" x 20
Cross journal diameter: 32/36 mm (1.26/1.42")
Cross length: 89/106 mm (3.50/4.17")
Closed, cross to cross: 51" (130 cm)
Open, cross to cross: 83" (211 cm)
Closed length (collapsed): 66" (168 cm)
Open length (extended): 105" (267 cm)
Power at 540 rpm: 110 hp
Power at 1000 rpm: 170 hp
Decoded: Plain half shaft, implement end

Match the tractor, not the implement. The shaft’s rating must meet or exceed your tractor’s PTO horsepower. Undersize it and the driveline becomes the part that fails.

Check your PTO speed. This shaft is rated 110 hp at 540 rpm and 170 hp at 1000 rpm. Use the figure for the speed you actually run — they are not interchangeable.

Working it hard? Bare Co advise reducing the rated horsepower by 40% for severe conditions — shock loading, heavy or wet crop, stony ground.

Length

Closed is the shaft fully collapsed — its shortest. Open is fully extended — its longest. Your tractor and implement must sit inside that range at every point through the turn.

Cross to cross is measured between the centres of the two universal joints. Overall is the full length including the end yokes. Most machine specs quote cross to cross.

This shaft trims to length. Measure your machine at its shortest point — the shaft must not bottom out — then cut to suit. You can always take metal off; you cannot put it back.

COMPLETES THIS DRIVELINE

110 HP Wide Angle Half Shaft, Tractor End1 3/8" x 6 tractor end · 66"–105"IHW36150

$1,042

110 HP Wide Angle Half Shaft, Tractor End1 3/4" x 20 tractor end · 66"–105"IHW3615020

$1,042

110 HP Wide Angle Half Shaft, Tractor End1 3/8" x 21 tractor end · 66"–105"IHW3615021

$1,042

FITS THESE MACHINES

Machine	Position	Tier
Massey Ferguson 2140	Implement end	Standard
Massey Ferguson 2160	Implement end	Standard
Massey Ferguson 2170	Implement end	Standard
Massey Ferguson 2170XD	Implement end	Standard
Massey Ferguson 2190	Implement end	Standard
Massey Ferguson 185	Implement end	Standard
Massey Ferguson 186	Implement end	Standard
Massey Ferguson 187LB	Implement end	Standard
Massey Ferguson 190LB	Implement end	Standard
Massey Ferguson 2150	Implement end	Standard
Massey Ferguson 2240	Implement end	Standard
Massey Ferguson 2250	Implement end	Standard
Massey Ferguson 2260	Implement end	Standard
Massey Ferguson 2270	Implement end	Standard
Massey Ferguson 2270XD	Implement end	Standard
Massey Ferguson 2290	Implement end	Standard

OTHER OPTIONS IN THIS SERIES

110 HP Half Shaft, Implement End1 3/8" x 6 implement end · 66"–105"OH36150

$330

1 3/8" x 6 implement end

110 HP Half Shaft, Implement End1 3/8" x 21 implement end · 66"–105"OH3615021

$330

1 3/8" x 21 implement end

110 HP Half Shaft, Implement End1 3/4" x 6 implement end · 66"–105"OH36150634

$330

1 3/4" x 6 implement end

110 HP Half Shaft, Implement End, Less YokeShaft less end yoke · 66"–105"OHE36150

$292

half shaft, implement end, less yoke